壓濾機入料泵的詳細介紹
一、YB 陶瓷柱塞泥漿泵
YB Ceramic Plunger Mud Pump
該泵能夠自動控制輸出流量且保證設定壓力不變,根據實際工況設定一個壓力值,當壓力升到設定值時壓力停止上升,此時泵的流量能在零到z大流量間根據實際需要自動改變運行速度并保持設定壓力不變。
由液壓驅動,壓力高,壓力調整快捷,運行平穩。采用α型氧化鋁陶瓷柱塞磨損小,操作安裝維護方便,使用成本低壽命長。
用途:用于陶瓷泥漿噴霧干燥、水煤漿高壓噴霧燃燒、清(污)水、各種懸浮液體、泥漿、含砂液體長距離輸送,也可用于壓濾機進料。
The pump can auto control flow volume and keep pressure no change, set a pressure value according the actual working condition, the pressure will stop increasing when the pressure reached to the settings, then flow volume of pump can range between 0 to max. to change the operation speed automatically according to the actual requirement and keep the pressure no change.
Driven by hydraulic, with high pressure, the pressure is adjusted accurately and quickly, operation smoothly. Using the α type Al-Oxide ceramic plunger to less wearing, easy for operation and maintenance, lower cost of using and long life time.
Usage: ceramic mud spray drying, water-coal-slurry spray burning, clean(dirty) water, all kinds of suspended liquid, mud, liquid with sand long distance transmitting, also can be used for the feedstock of filter press.
YB系列陶瓷柱塞泥漿泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85-2.8 | 2.8 | 0-2.5 | 2 | 220 | 4 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120-7.1 | 7.1 | 0-2.5 | 2 | 250 | 5.5/7.5 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB140-10 | 10 | 0-2.5 | 2 | 250 | 7.5/11 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB200D-24 | 24 | 0-1.5 | 1.5 | 250 | 18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB200-19 | 19 | 0-2.5 | 2 | 250 | 18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89’ |
YB250D-35 | 35 | 0-1.8 | 1.5 | 250 | 18.5 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB250-25 | 25 | 0-2 | 1.8 | 250 | 22 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB300D-45 | 45 | 0-1.8 | 1.3 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB300-40 | 40 | 0-2 | 1.8 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB300-35 | 35 | 0-2.2 | 2 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB300J-60 | 60 | 0-2.0 | 1.8 | 350 | 45 | 疊圈 | 2.0*1.3*2.4 | φ140/φ140 |
YB400D-100 | 100 | 0-1.5 | 1.2 | 350 | 55 | 疊圈 | 2.6*2.5*2.6 | Φ180/Φ159 |
YB500-150 | 150 | 2 | 1.8 | 450 | 110 | 疊圈 |
以上為基本型號,如需特殊需要可定制產品。
二、YB變頻陶瓷柱塞泥漿泵
YB convertion Ceramic plunger mud pump
采用PLC編程變頻器對泵進行控制,以針對不同工況和不同物料采用相應的程序來實現精確控制,可以提高工作效率,節約時間,還可以對泵的運行故障自動診斷報警。
用于壓濾機進料:可以對壓力和時間曲線的調整來實現,進料階段快速進料(節約時間),升壓階段,調整壓力上升快慢和上升時間長短(可以改變壓濾機貼近濾布層物料的密度來改善透水性,提高效率):保壓階段,可根據過濾所需實際壓力和流量自動調整到z佳輸出功率(節約能耗)。
用于高噴霧干燥!設定工作壓力,泵可以在保持設定壓力不變的情況下自動調整運行速度,達到無溢流運行,延長了液壓件的壽命,相比普通泵節能30%以上。
The pump is controlled by PLC programming convertor, by using the relevant program to get the accurate control to different working condition and materials, so as to increase the work efficiency, saving time, diagnosis alarm automatically to the working fault.
Using for feedstock of filter press: adjusted by pressure & time curve, shorten intake period (saving time), press period, adjusting the pressure changing speed and time changing speed (could change the density of material facing to filter cloth to enhance the water permeability, increasing efficiency); press keeping period, adjusting to best power output (saving energy) according to the actual pressure and flow volume needed.
Using for spay dry: set the working pressure, the pump could adjust the working speed automatically on the condition of setting pressure no change, to achieve the no over flow working, prolong life-span, above 30% energy saving to the common pump.
YB系列變頻陶瓷柱塞泥漿泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85P-2.8 | 2.8 | 0-2.5 | 2 | 220 | 5.5 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120P-7.1 | 7.1 | 0-2.5 | 2 | 250 | 7.5 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB140P-10 | 10 | 0-2.5 | 2 | 250 | 11 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB200P-24 | 24 | 0-2 | 1.5 | 250 | 18,5 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB250P-35 | 35 | 0-1.8 | 1.5 | 250 | 22 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB300P-45 | 45 | 0-1.8 | 1.3 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB400P-100 | 100 | 0-1.5 | 1.2 | 350 | 55 | 疊圈 | 2.8*2.5*3.2 | Φ180/Φ159 |
以上為基本型號,可按要求定制。
三、YB鈦合金耐腐柱塞泵
YB Titanium alloy corrosive-resisting Plunger Pump
性能特點:
該泵 利用鈦及鈦合金所具有的耐腐蝕、比重小、強度高、高低溫綜合機械性能好的特點,在所有接觸物料部分使用鈦或鈦合金制造。該泵具有優良的耐腐蝕性能,能耐大多數有機酸、無機酸、有機化合物以及堿、鹽溶液的腐蝕,適于輸送含有固體顆粒、易結晶介質,特別是用于長周期運行,提高了經濟性,具有結構簡單、密封可靠的優點。目前廣泛應用于制堿、制鹽、冶金礦山和石油化工等域。
Specification:
The pump is made by Titanium / alloys at all the medium part to material, since the Titanium / alloys has character of the corrosive-resisting, less density, high intension, high low temp comprehensive mechanic performance. The pump has the advanced the capability of corrosive-resisting, such as mostly organic Acid, inorganic Acid, organic chemical compound and Alkali, salty liquid, it’s good for the transmitting solid particle, easy crystaled medium, especially for long term operation, enhanced economics, with the feature of simple structure, reliable seal. Now is widely used for the manufacture of Alkali, Salt, Metallurgy and oil chemistry field.
YB鈦合金耐腐陶瓷柱塞泥漿泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85T-2.8 | 2.8 | 0-2.5 | 2 | 220 | 4 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120T-7.1 | 7.1 | 0-2.5 | 2 | 250 | 5.5/7.5 | YX | 1.6*1*1.6 | Φ76/Φ76 |
YB140T-10 | 10 | 0-2.5 | 2 | 250 | 7.5/11 | YX/疊圈 | 1.6*1*1.6 | Φ76/Φ76 |
YB200T-19 | 19 | 0-2.5 | 2 | 250 | 18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ89/Φ76 |
YB250T-30 | 30 | 0-2 | 1.8 | 250 | 18.5/22 | YX/疊圈 | 1.9*1.3*2.2 | Φ108/Φ89 |
YB300T-40 | 40 | 0-2 | 1.8 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ133/Φ133 |
YB300T-35 | 35 | 0-2.2 | 2 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ133/Φ133 |
以上為基本型號,可按要求定制。
四、YB高壓陶瓷柱塞泥漿泵
YB high pressure Ceramic Plunger Mud Pump
該泵為YB系列改進型,z高壓力為3Mpa,4Mpa,5Mpa三個等級,可輸送高濃度高粘度及含有顆粒的懸浮漿液,不用裝底閥可直接抽吸液體運轉平穩、噪聲小。結構簡單、拆裝維修方便。根據壓力合理選配電機,z大程度提高效率。
用途:高壓電瓷、日用瓷、各種高壓過濾、環保污水污泥處理及其他液體的遠距離輸送。
The pump is the modified product of YB serials, max pressure is 3Mpa,4Mpa,5Mpa, it can transmit serous fluid with high density, high viscosity and with suspend particle, it can pump the fluid directly without mounting bottom valve. The pump works stable, less noise, with simple structure, easy maintaining. It can choose the proper motor according to the working pressure to achieve the best efficiency.
Usage: high pressure electro ceramics, general ceramics, all kinds of high pressure filter, sewage treatment and other fluid long distance transmitting.
YB系列高壓陶瓷柱塞泥漿泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85G-2.8 | 2.8 | 0-3 | 2.8 | 220 | 4 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB85G-2.8 | 2.8 | 0-4 | 3.5 | 220 | 5.5 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB85G-2.8 | 2.8 | 0-5 | 4.5 | 220 | 7.5 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120G-7.1 | 7.1 | 0-3 | 2.8 | 250 | 7.5 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB120G-7.1 | 7.1 | 0-4 | 3.5 | 250 | 11 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB120G-7.1 | 7.1 | 0-5 | 4.5 | 250 | 15 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB140G-10 | 10 | 0-3 | 2.8 | 250 | 11 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB140G-10 | 10 | 0-4 | 3.5 | 250 | 15 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB140G-10 | 10 | 0-5 | 4.5 | 250 | 18.5 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB200G-17 | 17 | 0-3 | 2.8 | 250 | 18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB200G-17 | 17 | 0-4 | 3.5 | 250 | 22 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB200G-17 | 17 | 0-5 | 4.5 | 250 | 30 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB250G-25 | 25 | 0-3 | 2.8 | 250 | 30 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB250G-25 | 25 | 0-4 | 3.5 | 250 | 37 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB250G-25 | 25 | 0-5 | 4.5 | 250 | 45 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB300G-35 | 35 | 0-3 | 2.8 | 250 | 37 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB300G-35 | 35 | 0-4 | 3.5 | 250 | 45 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
YB300G-30 | 30 | 0-5 | 4.5 | 250 | 55 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
以上為基本型號,可按要求定制。
五、YB不銹鋼耐酸柱塞泵
YB stainless steel Acid-resisting plunger pump
該泵為輸送腐蝕性物料而設計。
由于耐酸不銹鋼有一定的抗晶間腐蝕能力,凡接觸腐蝕性物料介質的部分均為不銹鋼材料制作。采用陶瓷柱塞及耐酸堿密封,所以能輸送含腐蝕性物料,也可采用其他不銹鋼材料制作不會對輸送的物料產生二次污染。
用途:高嶺土、活性白土及含酸堿物料的輸送和高壓過濾,高壓電瓷原料的噴霧干燥及高壓過濾,食品原料的高壓輸送和過濾。
The pump is designed for the transmitting the corrosive materials.
Due to the intergranular resisting ability of Acid-resisting stainless steel, the medium to contact corrosive material is designed and made by stainless steel.
Using ceramic plunger and Acid-resisting seal, so the pump can transmit corrosive materials, also can be designed by other stainless materials to avoid the 2nd pollution the transmitting materials.
Usage: Kaolin, white bole and material with Acid/Alkali transmitting and filtration with high pressure; electroceramic material spray/dry and filtration with high pressure; foodstuff material transmitting and filtration with high pressure.
YB系列不銹鋼陶瓷柱塞泥漿泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85N-2.8 | 2.8 | 0-2.5 | 2 | 220 | 4 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120N-7.1 | 7.1 | 0-2.5 | 2 | 250 | 5.5/7.5 | YX | 1.6*1*1.6 | Φ76/Φ76 |
YB140N-10 | 10 | 0-2.5 | 2 | 250 | 7.5/11 | YX/疊圈 | 1.6*1*1.6 | Φ76/Φ76 |
YB200N-19 | 19 | 0-2.5 | 2 | 250 | 18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ89/Φ76 |
YB250N-30 | 30 | 0-2 | 1.8 | 250 | 18.5/22 | YX/疊圈 | 1.9*1.3*2.2 | Φ108/Φ89 |
YB300N-35 | 35 | 0-2.2 | 2 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ133/Φ133 |
YB300N-40 | 40 | 0-2 | 1.8 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ133/Φ133 |
以上為基本型號,可按要求定制。
六、YBB壓濾機專用泵
YBB specialized pump for filter press
該泵主要配合壓濾機使用,獨特的液壓回路設計,特別適合壓濾機在固液分離方面的應用。該泵能夠自動控制輸出流量且能保證設定壓力,根據過濾物料設定一個壓力值,當壓力升到設定值時壓力停止上升,此時泵的流量能在零到z大之間根據壓濾機實際需要自動切換單泵運行或雙泵運行,并保持設定壓力不變,故用此泵給壓濾機升壓時間短,保壓過濾功率低,壓力波動小,節約時間提高效率,相比其他壓濾機進泵節能30%。
The pump is designed for the filter press, unique design for the hydraulic circulation, fit for the application of separation of solid-liquid. The pump could control the flow volume output to keep the setting pressure automatically. Set a pressure value according to the filter, the pressure will stop increasing when the setting pressure is reached, then the flow volume can be adjusted from 0~max. according to the actual requirement, keep the setting pressure no change with switching to single pump or double pump automatically. So the pump could shorten the time of pressure, decrease the power consumption, less the pressure fluctuation, save time and more efficiency, with 30% energy saving comparing to the other products.
YB系列壓濾機專用變量泵參數表 | ||||||||
型號 |
額定流 量M³/H |
壓力范圍 MPA |
額定壓力 MPA |
沖程 MM |
配用電機 KW |
密封形式 |
外形尺寸 長*寬*高(M) |
吸/排漿管 直徑 |
YB85B-2.8 | 2.8 | 0-2.5 | 2 | 220 | 4 | YX/疊圈 | 1.2*0.85*1.5 | Φ57/Φ48 |
YB120B-7.1 | 7.1 | 0-2.5 | 2 | 250 | 5.5/7.5 | YX | 1.6*1*1.6 | Φ89/Φ76 |
YB140B-10 | 10 | 0-2.5 | 2 | 250 | 7.5/11 | YX/疊圈 | 1.6*1*1.6 | Φ89/Φ76 |
YB250B-19 | 19 | 0-2.5 | 2 | 250 | 15/18.5 | YX/疊圈 | 1.7*1.2*1.9 | Φ108/Φ89 |
YB250B-30 | 30 | 0-2 | 1.8 | 250 | 22 | YX/疊圈 | 1.9*1.3*2.2 | Φ133/Φ108 |
YB300B-40 | 40 | 0-2 | 1.8 | 250 | 30 | 疊圈 | 2.0*1.3*2.2 | Φ140/Φ140 |
以上為基本型號,可按要求定制。